Whirlpool Fridge Not Cooling: 8 Ways To Fix
Whirlpool fridges are designed to be used in households where people eat healthy meals.
These refrigerators are equipped with sensors that detect the presence of food items and automatically adjust the cooling system accordingly.
But if you notice that your fridge isn’t cooling down properly, here’s what you can do about it.
1.
Check whether the refrigerator door is open or closed.
If the door is open, check whether the power cord is plugged into the wall socket.
If not, plug it in.
2.
Make sure that the compressor is turned off.
Turn it off using the switch located near the back of the freezer
Whirlpool Fridge Not Cooling
If you have a whirlpool fridge not cooling problem, here are 8 ways to fix it.
1. Check if the compressor is working properly.
2. Make sure the thermostat is set correctly.
3. Check the fan switch.
4. Clean the condenser coils.
5. Check the drain pan.
6. Check the evaporator coil.
7. Check the ice maker.
8. Check the door seals.
1) Check The Condenser Coils
Check the condenser coils. This is the part of the refrigerator where the cold air comes from. It is located right behind the freezer section. To check the condenser coils, remove the back panel of the refrigerator. Look for two metal tubes, one on each side of the unit. These are called the condenser coils. The condenser coils are connected to the fan motor. If the condenser coils are clogged, the fan won’t run properly and the refrigerator won’t cool.
2 Check The Thermostat
Answer: Make sure the thermostats are set correctly. This is the part that tells the refrigerator when to turn on and off. To check the thermostat, open the door of the refrigerator and look for a round plastic button near the top of the door. Press down on the button until it clicks. Then press the button again to reset the setting.
2) The Temperature Settings
To change the temperature settings, follow these steps:
1 Open the door of the refrigerator.
2 Find the temperature buttons on the front of the refrigerator.
3) Motor
Motor is the heart of the refrigerator. It is responsible for keeping the cold air inside the fridge.
4 Compressor
Answer: Compressor is used to compress the refrigerant gas into liquid form. The compressor is located behind the motor.
4) Evaporator Motor
Evaporator motor is used to evaporate the moisture from the condenser coil. This helps in cooling down the system.
5 Condenser Coil
Answer: Condenser coil is used to cool the refrigerant gas coming out from the evaporator coil.
5) Start Capacitor
Start capacitor is used to store the energy required to start the compressor. It is connected between the power supply and the starting relay.
6 Relay
Answer: Relay is used to switch the electrical circuit.
6) Thermostat
Thermostat is used to regulate the temperature of the refrigeration system.
7 Compressor
Answer: Compressor is used to compress the gas into liquid state.
7) Start Relay
Start relay is used to turn on the compressor motor.
8 Refrigerant Line
Answer: Refrigerant line is used to connect the condenser coil to the evaporator coil.
8) Thermistor
Thermistor is used to measure the temperature of the refrigerant gas.
9 Expansion Valve
Answer: Expansion valve is used to regulate the flow of refrigerant from the condenser coil to evaporator coil.
If you notice any unusual noises coming from your refrigerator, such as rattling sounds, humming, or grinding noises, you should immediately contact a professional repair service. This is because these noises could indicate that something is wrong with your refrigerator. It is important to note that if you hear loud noises coming from your refrigerator compressor, you should not attempt to fix it yourself. Instead, you should call a professional repair service right away.
A whirlpool refrigerator has a reset button located near the top right corner of the door. This button allows you to turn off the compressor and restart the unit if it stops working. It is important to remember that the reset button does not affect the cooling system.
How do I reset my Whirlpool refrigerator compressor?
If your fridge was not working properly before the power went out, it is likely that it will continue to not function after the power goes back on. To fix this problem, you will need to unplug the appliance from the wall outlet and wait about 30 minutes before plugging it back in again. This will allow the electricity to flow through the circuit board and restart the unit. Once the unit is running normally, you can turn it back on and enjoy using it again.
How do I fix a Whirlpool refrigerator that is not cooling?
If your refrigerator is not cooling, check the thermostat. It could be stuck open, closed, or set to the wrong setting. Check the fuse box under the fridge. If the fuse box is good, check the breaker panel. If the breaker panel is good, check the circuit breaker itself. If the circuit breaker is good, check the wiring from the breaker to the outlet. If the wiring is good, check the outlet itself. If the outlet is good, check the power cord. If the power cord is good, check the plug. If the plug is good, check the appliance itself. If the appliance is good, check the fan motor. If the fan motor is bad, replace it. If the fan motor does not turn, check the filter. If the filter is clean, check the evaporator coil. If the evaporator coil is dirty, clean it. If the evaporator is dirty, clean it and try again. If the evaporator still does not cool, call a professional service technician.
How do I reset my Whirlpool refrigerator after a power outage?
To reset the compressor, turn off the power switch and wait about 30 seconds. Then turn the power back on and wait another 30 seconds. This process needs to be repeated until the compressor turns on.
The reset button is located on the back panel of the fridge. It is usually found near the power switch. Pressing the button will turn off the power to the unit. This will allow you to remove the battery from the front panel.
How do I reset my refrigerator compressor?
Whirlpool fridges have a reset button located on the back panel of the refrigerator. This button is used to turn off the power supply to the compressor. To turn on the power supply again, press the button twice.