Whirlpool Electric Range Cooktop Light Stays On: 5 Fixes

How often do you hear about electric ranges being recalled because they don’t turn off after cooking?
If you’ve ever had a Whirlpool range, you probably know that this problem has plagued them for years.

The Whirlpool company has issued several recalls over the last decade due to safety concerns.
In 2014 alone, the company recalled nearly 2 million units because of faulty thermostats.

This recall was prompted by reports from consumers who said their Whirlpool cooktops would stay on even though the burners were turned off.
This issue affected models dating back to 2004

Whirlpool Electric Range Cooktop Light Stays On

If your range light stays on after being turned off, check the following: 1 Make sure the power cord is plugged into the wall outlet. 2 Check the fuse box under the sink. 3 Reset the timer if needed. 4 Turn off the gas supply valve. 5 Clean the oven door gasket. 6 Replace the oven door gasket if necessary. 7 Remove any obstructions from the oven door opening. 8 Check the oven thermostat. 9 Repair any loose wires. 10 Clean the oven interior. 11 Clean the oven exterior. 12 Adjust the oven thermostat setting. 13 Check the oven heating element. 14 Check the oven ventilation fan. 15 Clean the oven exhaust vent. 16 Check the oven lighting circuit. 17 Check the oven light switch. 18 Check the oven light bulb. 19 Check the oven light wiring. 20 Check the oven light fixture. 21 Check the oven light socket. 22 Check the oven light cord. 23

1) Circuit Board

2 Fuse Box
Answer:

reset the electric cooktop

1 Reset the electric cooktop
2 Remove the fuse box from the wall

replace it with a new one

2 Short switch

3) Resetting The Power

1 Pressing the power button 3 times quickly
2 Pressing the reset button 5 times quickly

taking out the power cable

3 Resetting The Power 1 Pressing the power button three times quickly 2 Pressing the reset button five times quickly taking out the power cable

switching off the circuit breakers

1 Pressing the power button 3 times quickly
2 Pressing the reset button 5 times quickly
taking out the power cable
switch off the circuit
breaker

4) Sensor Issue

1. Check if the sensor is properly installed.
2. Check if the sensor has been
damaged.

wait until the cooktop cools down

4 Sensor Issue
1 Check if the sensor is correctly installed.
2 Check if the sensor has damage.
3 Wait until the cooktop cool
down.

press and hold the control lock pad for around five seconds

5 Control Lock
Press and hold the control lock button for around five seconds. This will open the door automatically.

Why is my cooktop light staying on?

Yes, there is a reset button on the front panel of your Whirlpool stove. It is located near the top left corner of the front panel. To access the reset button, press the power button and hold it down until the display turns off. Then release the power button and the display will turn back on.

Why wont my cooktop light go off?

To reset your cooktop, simply turn off the power switch located on the back panel of your range. Next, press and hold down the reset button until the display turns off. Finally, release the reset button and wait for the display to turn on again.

How do I reset my Whirlpool cooktop?

Cooktop lights are used to illuminate the surface area of the cooktop. This helps to see what you are doing while cooking. The cooktop light goes off if the power supply is not working properly. It could be because of a faulty switch or fuse. In case the switch is bad, replace it immediately.

Is there a reset button on my Whirlpool stove?

Cooktops are designed to burn fuel, but if the flame isn’t lit, it won’t produce any heat. It’s possible that the pilot light is not working properly. Try lighting the burner again and see if it lights. If it doesn’t, try turning off the gas supply to the stove, wait 30 seconds, turn the gas back on, and check if the light comes back on. If it does, the problem could be caused by a faulty switch. If the light stays on after the gas is turned off, the problem could be a blown fuse. Call a professional electrician to repair the circuit board.

Similar Posts