Maytag Dishwasher Start Button Not Working: 3 Fixes
How often does your dishwasher break down?
If it happens frequently, then you might want to consider replacing your Maytag dishwasher.
This appliance has a reputation for being unreliable.
In fact, it was named the worst washing machine brand in America by Consumer Reports.
Dishwashers are designed to wash dishes at high speeds.
They also come equipped with sensors that detect when they are full or dirty.
When these sensors fail, it can cause your dishwasher to stop working properly.
There are three common ways to fix your Maytag dishwasher: replace the sensor, replace the motor, or replace the control board.
These fixes are detailed below
Maytag Dishwasher Start Button Not Working
If you have a Maytag dishwasher and the start button does not work, here are three fixes you can try. First, check if the power cord is plugged into the wall socket correctly. Second, check if the dishwasher is turned off. Third, check if the door switch is working properly.
1) Touchpad Fault
Touchpad fault occurs when the touch pad is not responding to any commands. This problem can occur because of the following reasons:
a The touch pad is damaged.
b The touch pad is dirty.
2) Touchpad and control panel
Touchpad and control panel faults can occur because of the below mentioned reasons:
a The control panel is damaged.
b Control panel is dirty.
3) A problem in the main control board
1 Touch pad and control panel fault occurs because of the below mentioned reason:
a The touchpad is damaged.
Why will my Maytag dishwasher not turn on?
Yes, there is a reset button on the top panel of the dishwasher. It is located near the door handle. To reset the timer, press and hold the button until the display changes from “Timer Reset” to “Reset Timer”. Then release the button. This will stop the dishwasher from counting down and begin the wash cycle again.
If you notice that your dishwasher isn’t starting, check the power cord first. Make sure that the plug is firmly inserted into the wall outlet. Next, check the fuses. If these aren’t blown, try unplugging the appliance from the wall outlet and plugging it back in again. If none of these steps resolve the issue, call a professional repairman.
How do you run a diagnostic test on a Maytag washer?
If you cannot locate the reset button, try pressing the door handle. This usually resets the timer. If that does not work, press the power switch on the back of the unit. This usually resets any timers. If none of these work, call Maytag customer service.
How do you run a diagnostic test on a Maytag dishwasher?
If you notice that your dishwasher won’t turn on after you’ve pressed the start button, check if the power cord is plugged into the wall socket correctly. Also, try unplugging and replugging the power cord. If these steps still don’t solve the problem, contact your local appliance repair service.
To diagnose a problem with your Maytag dishwasher, follow these steps: 1 Turn off the power switch 2 Remove the door panel 3 Unplug the unit 4 Disconnect the drain hose 5 Check the drain pump 6 Check the filter 7 Check the heating element 8 Check the washer motor 9 Check the detergent dispenser 10 Check the soap dispenser 11 Check the rinse aid dispenser 12 Check the air vent 13 Check the drain pump 14 Check the drain hose 15 Check the filter 16 Check the heating element 17 Check the washer motors 18 Check the detergent 19 Check the soap 20 Check the rinse aid 21 Check the air vent 22 Check the drain pump 23 Check the drain hose 24 Check the filter 25 Check the heating element 26 Check the washer 27 Check the detergent 28 Check the soap 29 Check the rinse aid 30 Check the air vent 31 Check
Maytag washers are built to last. However, if you notice any problems with your washing machine, such as loud noises, excessive vibrations, or leaking water, it is important to contact a professional service technician immediately. A Maytag repairman will be able to diagnose the problem and provide you with a solution.
How do you reset a dishwasher that won’t start?
Dishwashers are very important appliances in every household because they help us clean our dishes efficiently. But sometimes we face problems while using them. One of the common issues is the problem of starting the dishwasher. This happens when the buttons of the dishwasher are not working properly. It could happen if the power supply is faulty or the circuit board is damaged. So, check whether the power supply is connected correctly. Also, check whether the fuses are blown. If these two points are fine, then the problem could be with the buttons. In case, the buttons are not working, try pressing the reset button. If the problem persists, call the service center.
If you see a message saying “Dishwasher error code 1” on your display screen, you need to call the service center immediately. This error code indicates that the door sensor switch has failed. It could be because of a loose connection between the door sensor switch and the door motor. In such cases, the door sensor switch needs to be replaced.