Maytag Centennial Washer Won’t Spin: 5 Ways To Fix

How often does your washing machine break down?
If you’re having problems with your washer, then you probably don’t want to spend hours or even days trying to fix it.
Instead, why not try these five simple fixes instead?

Washing machines are essential appliances in every household.
They clean clothes, remove stains and freshen up your home.
Unfortunately, they also tend to break down quite frequently.
The Maytag Centennial Washer won’t spin is one of the most common problems faced by consumers.

Here are some ways to fix the problem

Solutions for the Maytag Centennial Washer Won’t Spin Issue

If you are experiencing issues with your washer not spinning, here are five ways to fix it.
1. Check the Power Cord
Make sure your power cord is plugged into a working outlet. If you notice any loose connections, tighten them immediately.

Redistribute the Laundry Load

You could try redistributing the laundry load. This way, the clothes won’t get tangled together and the washer will spin properly.
2. Check the Drain Pump
Check if the drain pump is working correctly. If it isn’t, check the hose connection and make sure it is secure.

Check the Lid Switch

If the lid switch doesn’t turn off the power, the lid switch needs to be replaced.
3. Check the Washer Motor
If the motor is not turning, check the belt. It should be tightened.

Clean the Drain Hose

Check if the drain hose is clogged. Clean the drain hose using a brush.
4. Check the Oven Door Sensor
If the oven door sensor does not detect the opening of the oven door, replace the sensor.

Inspect the Washer Drum

1. Remove the washer drum from the washing machine.
2. Inspect the washer drum for any damage.

Inspect the Drive Belt

1. Check the drive belt for wear and tear.
2. Check the tensioning nut for looseness.
3. Check the pulley for wear and tear.

## FAQs

How do you fix a Maytag washer that will not spin?

Maytag washers have two motors: One motor spins the agitator the part that cleans clothes and another motor spins the wash tub. If the motor that spins the tub fails, the washer won’t spin. To fix this problem, you’ll need to replace the tub motor.

How do I reset my Centennial Maytag washer?

Maytag washers are built to last but if they break down they can be very expensive to repair. It is important to check the manual to see what needs to be done to fix the problem. Most likely it is something simple such as a fuse or switch. If the problem persists contact a professional appliance service technician.

How do I reset my Maytag washer?

To reset the spin cycle on the Maytag washer, turn off the power switch and wait about 30 seconds. Then press and hold the “Start” button until the display explains “Reset”. Press the “Start’ button again to confirm the setting.

How do I reset my spin cycle?

If you notice that your washer is spinning but not doing anything else, check the door seals. Washers usually have two doors, one on each side of the tub. Make sure that these doors are closed tightly and that they are not leaking any water. If you still notice that the washer is spinning but nothing is happening, try unplugging the unit and plugging it back in again. If this does not help, contact your local repairman.

How do I fix the spin cycle on my washing machine?

To reset the timer, simply press the “start” button again. To turn off the machine, press the power button until the display turns off. Once the display goes dark, the machine is turned off.

How do you reset the spin cycle on a Maytag washer?

To reset your Maytag washing machine, simply turn off the power switch located near the front of the unit. Next, remove the two screws holding the top panel on. Then, lift the top panel up and slide it back into place. Finally, replace the screws and turn the power switch back on.

How do I get my Maytag washer to spin?

To reset the washing machine, remove the access panel from the top of the machine. Open the door and remove the screws holding the door in place. Remove the door and set aside. Next, remove the two screws holding the front panel in place. Lift the panel off the machine and slide it forward until it stops. Slide the panel back into place and replace the screws. Replace the door and turn the knob to lock the machine. To reset the dryer, remove the access panel located on the left side of the machine. Remove the three screws holding the panel in place. Remove the panel and slide it forward until the stop engages. Slide the panel back in place and replace the screws and the door. Turn the knob to lock the unit.

Why does my Maytag washer not spin?

If you have a washing machine that won’t spin, check the belt. It’s possible that the belt is worn out. To replace the belt, remove the top panel from the front of the machine. Remove the screws holding the panel in place. Then lift off the panel. Look under the panel for the belt. If you see a worn belt, replace it. If you don’t see a belt, check the motor. If the motor is bad, it could be replaced. If the motor is good, but the belt is worn out, it could be repaired. If the motor is working fine, but the belt is still worn out, it could possibly be replaced.