Kitchenaid Dishwasher Thermal Fuse Keeps Blowing: 6 Fixes

How often does your dishwasher blow out the thermal fuse?
If you’ve had this problem before, you probably thought that it was a simple fix.
But did you ever wonder why your dishwasher keeps blowing the fuse?
Read on to discover some common causes and solutions.

Dishwashers are great appliances, but they can also be quite temperamental.
The thermal fuse is a safety device that prevents overheating inside the machine.
When the fuse blows, the water pump shuts off and the cycle stops until the fuse is replaced.

Here are six reasons why your dishwasher might be blowing its fuse.
And then, here are six fixes for each reason

Kitchenaid Dishwasher Thermal Fuse Keeps Blowing

If you see a red light flashing on your dishwasher, it could mean that the thermal fuse has blown. This is not something that needs to be repaired right away, but it does indicate that the dishwasher is overheating. It’s important to note that if the thermal fuse blows while the dishwasher is running, it could damage the motor. To fix this problem, follow these steps:
1. Turn off the power to the unit.
2. Remove the back panel from the bottom of the dishwasher.

1) Loose Contact

There are two types of fuses used in appliances: A fuse is a circuit breaker that opens when current exceeds a certain level. In other words, it protects electrical components from being damaged by excessive current. A fuse is rated according to the maximum amperage it can safely carry. For example, a 20 amp fuse can handle up to 20 amps of current.
A thermal fuse is designed to protect the appliance from overheating. It is usually located near the heating element thermal fuse. When the heating element gets hot enough, the thermal fuse melts and opens the circuit.

2) Power

Power is the rate at which energy flows through a conductor. Energy is measured in joules J, watts W, or kilowatts kW.
3 Circuit Breaker
Answer: A circuit breaker is a switch that interrupts power to a section of a circuit. It is typically installed between the source of electricity and the load. A circuit breaker is designed to interrupt the flow of electricity if something goes wrong with the wiring or equipment connected to it.

3) Door Switch

A door switch is used to turn lights on and off from a remote location. It consists of two parts; a sensor that detects motion and sends a signal to a light switch, and a light switch that turns the lamp on or off depending on whether the sensor detects movement.
4 Light Switch
Answer: A light switch is a device that controls electrical lighting circuits. It allows users to turn lights on and/or off.

4) Wiring

Wiring is the process of connecting wires together to form a circuit. In order to connect wires together, we use connectors such as wire nuts, crimps, and splices.
5 Circuit Breaker
Answer: A circuit breaker is a safety device that protects people and property from dangerous electricity. It stops power from flowing if something goes wrong with the wiring.

5) The Wattage

A watt is a unit of electric energy. One watt is equal to 1 joule per second J/s.
6 Voltage
Answer: Voltage is the potential difference between two points. For instance, 120 volts is the voltage across a 120 volt AC outlet.

6) Water Leaks

Water leaks occur when there is a leak in the pipe system. It happens because of the expansion of air in pipes. This leads to the formation of cracks in the walls of the pipes. These cracks allow the water to seep into the wall.
7 Overheating
Answer: Overheating occurs when the temperature of the equipment exceeds its normal operating range. In case of ovens, overheating usually occurs when the temperature reaches above 350 degrees Fahrenheit 180 degrees Celsius.

Why does my dishwasher cause a power cut?

A thermal fuse looks like a long thin wire with two ends. One end is connected to the heating element and the other end is attached to ground. A thermal fuse is used to protect against overheating of the heating element. It is designed to blow if the element gets too hot. This prevents damage to the unit.

How do I know if my dishwasher thermal fuse is blown?

Thermal fuses blow because of overheating. This happens when the heating element gets too hot and melts. It could happen if the element is defective or if the element is not properly connected.
If you notice any signs of melting plastic, check the wiring connections. Make sure that the wires are firmly attached to the terminals. Also, ensure that the power cord is plugged into the wall outlet correctly.

How do you reset the thermal fuse on a dishwasher?

To perform a hard reset on a Dishwasher, turn off the power switch if applicable and unplug the unit from the wall outlet. Then, remove the door panel and disconnect the electrical connectors from the back of the unit. Next, press and hold the reset button until the display explains “Reset” and release the button. Finally, plug the unit back into the wall outlet and turn the power switch back on.

How do I know if my dryer thermal fuse is blown?

If your dryer doesn’t seem to be working properly, check the fuses located under the top panel of the dryer. These fuses should be checked every year. If any of these fuses blow, replace them immediately. This could mean that your dryer is not getting enough power from the electrical outlet. It could also mean that the dryer is overheating. Check the thermostat on the back of the dryer. If the dial is set to “off”, turn it to “heat”. If the dial is already set to “heat“, try turning it down to “warm�”. If the dryer still isn’t heating, check the wiring harness. Make sure that the wires aren’t frayed or loose. Also, check the connection between the dryer motor and the wall socket. If the connection looks bad, replace it.

How do you do a hard reset on a dishwasher?

If you notice that the dishwasher isn’t heating properly, check the thermal fuse. It is located near the door handle. Resetting the fuse is easy. Simply remove the two screws holding the fuse in place and replace it. This will ensure that the dishwasher heats properly again.

Why does my thermal fuse keep blowing on my dishwasher?

If your dishwasher is not working properly, check the fuses located near the bottom of the unit. These fuses are designed to protect against overheating and short circuits. If any of these fuses blow, replace them immediately.

What does a thermal fuse look like when it’s blown?

Dishwashers are designed to wash dishes quickly, but they can take longer than expected if you leave dirty dishes in the washer overnight. This can happen because the detergent needs to break down the grease and grime from the dishes. It takes a while for the detergent to do its job, so if you leave dirty dishes overnight, the next day the detergent won’t be able to clean the dishes properly. This can result in a power outage.