3 Ways To Troubleshoot Kenmore French Door Bottom Freezer Ice Maker Not Working
Kenmore French door bottom freezer ice maker not working is a common problem among people who own these appliances.
It happens because of several reasons such as low power supply, bad wiring, faulty motor, broken wires, damaged compressor, blocked drain line, clogged filter, and many others.
In order to troubleshoot this issue, you need to check the following points:
1 Check if the unit is plugged into a good electrical outlet.
2 Make sure that the unit is turned off
How to Troubleshoot Kenmore French Door Bottom Freezer Ice Maker Not Working?
Kenmore French door bottom freezer ice maker not working is a common problem among people who own these appliances. This is because the ice maker is located underneath the refrigerator cabinet. It is very difficult to access the ice maker from outside the refrigerator. So if you are facing this issue, here are three ways to troubleshoot kenmore french door bottom freezer ice maker.
1 Check the power supply. Make sure that the power cord is plugged into the wall socket properly. Also check whether the fuse is blown. Fuse blows usually happen during heavy usage of the appliance.
2 Check the wiring connections. Look for loose wires or damaged wires. Sometimes the wires get disconnected while using the appliance.
Checking the Ice Maker Switch
If you are having problems with the ice maker switch, try checking the switch itself. First, turn off the power to the unit. Then open the back panel of the refrigerator and remove the two screws holding the switch in place. Remove the switch and inspect it carefully. If the switch is bad, replace it.
Defective Thermostat
Thermostats are used to regulate the temperature inside the refrigerator. It is important to check the thermostat every month to ensure that it is working properly. A defective thermostat could lead to excessive energy consumption and higher utility bills. Check the thermostat for any signs of damage or corrosion. Replace the thermostat if necessary.
Defective Water Filter
Getting It Checked
Water filters remove impurities from tap water. These contaminants can cause health problems such as stomach upset, diarrhea, skin rashes, eye irritation, and other infections. To protect yourself against these health risks, you should get your water filter checked periodically.
Checking Your Water Filter
To check your water filter, turn off the faucet and open the drain valve. Remove the filter cartridge and inspect it for cracks or leaks. Clean the filter cartridge using a soft brush or sponge. Replace the filter cartridge if necessary.
How do I reset my Kenmore bottom freezer ice maker?
If the ice maker does not produce any ice after several attempts, try cleaning the ice tray. Remove the ice tray from the freezer and wipe down the tray with a damp cloth. Make sure the tray is dry before putting it back into the freezer. If the problem persists, contact the manufacturer for assistance.
How to clean an ice maker?
Why is there no water going into my ice maker?
To reset a freezer ice maker, turn off the power switch and wait about 30 seconds. Then, press and hold the “Reset” button until the display explains “OK”. Press and release the “Reset” button again. After the display explains “Ready”, press and release the “Start” button. Wait about 10 minutes for the unit to start making ice.
Kenmore icemaker problems are usually caused by clogged filters. To check if the filter needs cleaning, remove the back panel from the machine. Look for a plastic filter that sits above the evaporator coil. Remove the filter and wash it with warm water. Replace the filter and reassemble the machine. If the problem still exists, call a service technician.
What to check if ice maker stops working?
To clean the ice maker, simply open the door and pour warm water down the drain tube. Then, turn off the power to the unit. Once the power is turned off, wait about 30 minutes for the ice maker to cool down. After the ice maker has cooled down, disconnect the power cord and remove the ice tray. Clean the ice maker using soap and hot water. Rinse the ice maker thoroughly and dry it completely. Reattach the ice tray and replace the door.
Why is my Kenmore freezer not making ice?
If the water level indicator light is flashing red, the problem could be caused by a clogged drain line. To clear the blockage, remove the ice tray from the freezer and run cold water through the drain line until the water runs clear. Remove any debris that was caught in the drain line. Replace the ice tray back in the freezer.
How do I clean my ice maker?
How do you troubleshoot a Kenmore ice maker?
To reset the ice maker on the LG refrigerator, press and hold the power button for about 10 seconds. Then release the power button and wait for the display to turn off. Next, press and hold the Power/menu button for about 5 seconds. Release the Power/menu button and wait for the screen to return to normal mode.
How do you reset the ice maker on a Maytag refrigerator?
1. Press and hold the power button until the display turns off.
2. Press and hold the Power/Menu button until the display turns back on.
How do you reset a freezer ice maker?
If you are having problems with your Kenmore refrigerator freezing, check the following items: Make sure the freezer is plugged in and turned on. Check the temperature setting on the thermostat. If the temperature is set too low, the freezer won’t freeze. If the temperature is too high, the freezer won’t cool down enough to make ice. Check the door seals. If the door seals aren’t sealed properly, cold air will leak out. This could prevent the freezer from cooling down. Check the filter. If the filter is clogged, it could prevent the freezer from working properly. Clean the evaporator coils. If the coils are dirty, they could prevent the freezer from functioning properly. Clean the fan motor. If the fan motor isn’t working correctly, it could cause the freezer to stop working. Check the drain pan. If the drain pan isn’t draining properly, it could prevent the ice maker from working properly. Check the ice bin. If the ice bin isn’t full, it could prevent the machine from making ice. Check the ice maker’s circuit board. If the circuit board is damaged, it could prevent the unit from operating.
To reset the ice maker, follow these steps: 1 Unplug the unit from the power source; 2 Remove the ice bin door if applicable; 3 Press and hold the “Reset” button on the front panel for 10 seconds; 4 Plug the unit back into the power source.
How do you clean a Kenmore bottom freezer ice cube tray?
Yes, they do. But if you press the reset button, it won’t turn off the ice maker. It will only stop making ice. To turn the ice maker back on, you’ll need to unplug it from the wall outlet. Then plug it back in and wait until the ice maker turns itself off. Once it does, you can press the reset button again to get it started making ice again.